Hot Tub Compatible With Watkins Spas Pressure Switch Hot Spot Solana 71586 3903

Description

Watkins Spa Pressure Switch Hot Spot & Solana 71586 / 3903. This pressure switch (looks like a radiator thermostat) is a safety device that screws into the heater that will shut down the heater if a "low water flow" condition occurs. It is used on all 1999-2005 Hot Spot spa models as well as all 2000-2002 Solana X, 2003-2005 Solana RX, SX & TX spa models.
This is for a Single Item
PRESSURE SWITCH REMOVAL
1. Disconnect power to the spa.
2. Remove the front access panel.
3. Drain the spa.
4. Open the
drain valve
to bleed the water out of the plumbing.
5. Open the
control box
lid.
6. Disconnect the pressure switch connection wires from the pressure switch.
7. Unscrew the pressure switch from the heater and remove any residual Teflon tape from the
threads of the heater body where the pressure switch was connected.
RE-INSTALLATION
Reverse the removal procedure to install the pressure switch in the control box.
NOTE:
Wrap one piece of Teflon tape (in the opposite direction of the threads) three times
around the pressure switch threads before installation. When screwing the new pressure switch into the heater, DO NOT use pliers, grasp the body of the pressure switch and hand tighten only. After you are finished with the installation, switch the jet pump to high speed and check the pressure switch for leaks.
STORE
FEEDBACK
CONTACT US
ADD TO FAVORITES
BBQ REPAIR KITS
FOUNTAIN REPAIR PARTS
FIREPLACE REPAIR PARTS
HOT TUB REPAIR PARTS
PLUMBING REPAIR PARTS
PATIO HEATERS
PRODUCTS CATEGORIES
ALL
BBQ REPAIR KITS
FOUNTAIN REPAIR PARTS
FIREPLACE REPAIR PARTS
HOT TUB REPAIR PARTS
PLUMBING REPAIR PARTS
POOL
PATIO HEATERS
OTHER
Watkins Spa Pressure Switch Hot Spot & Solana 71586 / 3903
Watkins Spa Pressure Switch Hot Spot & Solana 71586 / 3903. This pressure switch (looks like a radiator thermostat) is a safety device that screws into the heater that will shut down the heater if a "low water flow" condition occurs. It is used on all 1999-2005 Hot Spot spa models as well as all 2000-2002 Solana X, 2003-2005 Solana RX, SX & TX spa models.
This is for a Single Item
PRESSURE SWITCH REMOVAL
1. Disconnect power to the spa.
2. Remove the front access panel.
3. Drain the spa.
4. Open the
drain valve
to bleed the water out of the plumbing.
5. Open the
control box
lid.
6. Disconnect the pressure switch connection wires from the pressure switch.
7. Unscrew the pressure switch from the heater and remove any residual Teflon tape from the
threads of the heater body where the pressure switch was connected.
RE-INSTALLATION
Reverse the removal procedure to install the pressure switch in the control box.
NOTE:
Wrap one piece of Teflon tape (in the opposite direction of the threads) three times
around the pressure switch threads before installation. When screwing the new pressure switch into the heater, DO NOT use pliers, grasp the body of the pressure switch and hand tighten only. After you are finished with the installation, switch the jet pump to high speed and check the pressure switch for leaks.
SEE OUR OTHER ITEMS
Clear Spa Bromo Boost 2 Ounce 6 Packets HTCPCSSO002Z-6
.98
SHOP NOW!
Dimension One Spa Floor Drain Cover - Gray DIM01510-231G
.44
SHOP NOW!
Clear Spa Bromo Boost 2 Ounce Single Packet HTCPCSSO002Z
.98
SHOP NOW!
Dimension One Spa Floor Drain Cover - White DIM01510-231
.44
SHOP NOW!
PAYMENT
SHIPPING
RETURNS
PAYMENT
PAYMENT
SHIPPING
RETURNS
PAYMENT
Double click to edit
PAYMENT
SHIPPING
RETURNS
SHIPPING
PAYMENT
SHIPPING
RETURNS
SHIPPING
Double click to edit
PAYMENT
SHIPPING
RETURNS
RETURNS
PAYMENT
SHIPPING
RETURNS
RETURNS
Double click to edit
STORE
FEEDBACK
CONTACT US
ADD TO FAVORITES